20-0
THE FOOTBALL ROSTER-BUILDING CHALLENGETHE DRAFT ROOM PLAYBOOK
🏟️  KNOW THE JOB BEFORE THE NAME

20-0 Roster Positions

Twelve slots form this drafting model: six offense and six defense. Learn the named jobs first, then use the map to distinguish an open destination from extra eligibility.

🏟️ A compact roster, not eleven players on a field

The twelve 20-0 roster positions form a drafting model. They are not an on-field formation with eleven athletes lined up for a snap. The model gives each side six contributions, including flexible spaces that let you use another eligible player without inventing a new fixed role.

Start by recognizing the named jobs. Offense has a quarterback, running back, wide receiver, and tight end, plus two FLEX selections. Defense has an edge rusher, defensive tackle, linebacker, cornerback, and safety, plus D-FLEX. Both sides matter to completing the full run.

Offense · six selections
QBQuarterback
RBRunning back
WRWide receiver
TETight end
FLEXOffensive skill
FLEXOffensive skill
Defense · six selections
EDGEEdge rusher
DTInterior defense
LBLinebacker
CBCornerback
SSafety
D-FLEXFlexible defender

This is a slot map for the draft, not a tactical alignment or a live formation editor.

The offensive vacancies are not interchangeable

The standard QB card has one route: the empty QB destination. RB, WR and TE have their named destinations plus available offensive FLEX. That difference makes the map useful before any ranking: first find the legal set, then compare the cards inside it.

That means two equally legal placements can leave different future needs. Assigning a tight end to TE resolves a particular job. Assigning him to FLEX may preserve the same player contribution, but the specific tight-end requirement still needs an answer later.

Count the jobs left, not just the number of impressive names you have collected. In the captured offensive lineup, the surnames in filled slots make that count visible without reopening every player card.

Read the remaining jobs.Occupied buttons tell you what has already been covered in this run.

🛡️ Five defensive names worth learning

EDGE and DT

EDGE describes an outside pass-rushing role. DT identifies interior defensive-line play. Both can appear with sack production, but a shared statistic does not make their roster labels interchangeable.

LB

Linebackers can have varied jobs: tackling, rushing, or coverage. Read the available card’s position and any additional eligibility rather than deciding its slot from a single impressive tackle total.

CB and S

Cornerback and safety are separate secondary roles. Both can record interceptions. A takeaway is evidence about a play; it is not proof that a safety card fills the dedicated cornerback vacancy.

D-FLEX

The flexible defensive destination accepts eligible defenders. It gives you one place to use another strong defensive option while the named jobs still need to be completed.

Need help decoding the defensive columns? The stat reference explains the labels without treating every defender as the same type of player.

Where does a standard single-role card fit?

Primary roles and their standard roster destinations
Card roleDedicated destinationFlexible alternative
QBQBNo standard offensive FLEX placement
RBRBEither available offensive FLEX
WRWREither available offensive FLEX
TETEEither available offensive FLEX
EDGEEDGEAvailable D-FLEX
DTDTAvailable D-FLEX
LBLBAvailable D-FLEX
CBCBAvailable D-FLEX
SSAvailable D-FLEX

An additional position printed on a particular card can expand its choices. This table describes standard primary roles; the game’s live highlights settle the eligibility of the card you selected.

When defense starts, reset your mental checklist

Finishing offense is a phase change. The next six selections need a different set of positions, even though the actions still look familiar. An offensive surname you recognize does not help if the active board is asking for defenders.

At the handoff, check for six defensive vacancies and read the active side label. The new list is EDGE, DT, LB, CB, S and D-FLEX. A player left in an offensive filter or remembered from the previous offer is not an extra defensive selection.

This is also where unfamiliar abbreviations can lead to rushed assumptions. EDGE is not a catch-all label for anyone who made sacks, and CB is not a generic label for every secondary player. Read the actual card.

A different six jobs.The defensive slot labels replace the offensive set when that half begins.

Count the vacancies on a practice roster

Mark the positions you have filled in a practice example. This small counter does not read or change the embedded game; it simply makes the twelve-position requirement easier to check.

12 open slots: 6 offense and 6 defense.

Two placement cases that expose the difference

A second running back arrives early

Your RB position is occupied and both FLEX positions are available. Another eligible running back has a legal destination, but drafting him consumes flexible room. That does not help the empty WR or TE slot. Decide whether the added player is worth the tighter shape of the remaining offense.

A versatile defender arrives late

Only LB and D-FLEX remain open. A card explicitly eligible at linebacker can be placed at LB, leaving D-FLEX able to accept a later eligible defender. Using D-FLEX first can be legal, yet leave you needing a specific linebacker afterward. The value of a placement includes the shape it leaves behind.

Use this map when you need to answer “where can this card go?” Use the placement-path examples when two legal homes compete. The selection controls explain how to confirm the assignment, and position weighting explains its place in the evaluation.

Keep the reference handy, then make the next choice on the actual draft board.

Play 20-0
Inside the draft